FAQ
- M051 Base Series(95)
- M0518 Series(97)
- M0519 Series(43)
- M0564 Series(1)
- Mini51 Base Series(90)
- Nano100/102 Base Series(101)
- Nano103 Base Series(10)
- Nano110/112 LCD Series(100)
- Nano120 USB Series(111)
- Nano130 Advanced Series(110)
- NUC029 Series(94)
- NUC100/200 Advanced Series(102)
- NUC120/122/123/220 USB Series(116)
- NUC121/125 Series(1)
- NUC126 USB Series(2)
- NUC130/230 CAN Series(103)
- NUC131/NUC1311 CAN Series(98)
- NUC140/240 Connectivity Series(114)
- M451 Base Series(118)
- M451M Series(117)
- M452 USB Series(130)
- M4521 USB Series(1)
- M453 CAN Series(128)
- M463 CAN FD/USB HS Series(1)
- M467 Ethernet/Crypto Series(1)
- M471 Series(1)
- M479 Motor Control Series(1)
- M481 Base Series(4)
- M482 USB FS OTG Series(4)
- M483 CAN Series(4)
- M484 USB HS OTG Series(4)
- M485 Crypto Series(4)
- M487 Ethernet Series(4)
- M4TK Touch Key Series(25)
- NUC442/472 Series(130)
- NUC472 Series(1)
- NUC505 Series(138)
FAQ
What are ISP, ICP and IAP? Issue Date：2015-02-09
ISP stands for "In System Programming". The target chip runs the boot/loader code of LDROM through the peripheral interface such as USB/UART/SPI/I²C/RS-485/CAN... to update the internal APROM, Data Flash and User Configuration Word.
ICP stands for "In Circuit Programming". PC runs the software “NuMicro ICP Programming Tool” through the SWD (serial wire debug) port of Nu-Link circuit to update the internal APROM, LDROM, Data Flash and User Configuration Word of the target chip.
IAP stands for In-application-programming and it is a function for user to switch the code executing between APROM and LDROM without reset. User can enable the IAP function by re-booting chip and setting the chip boot selection bits in CBS (CONFIG0[7:6]) as 2 or 0. When chip boots with the IAP function enabled, any other page within the executable range of code can be mirrored to the first page of executable code (0x0000_0000~0x0000_01FF) any time. User can change the remap address of the first executing page by filling the target remap address to ISPADR and then go through ISP register with the Vector Page Re-map command. After changing the remap address, user can check if the change is successful by reading VECMAP(ISPSTA[20:9]).
(Below figure is the example for executable range of code with IAP Function Enabled of M05xDN/DE series.)
| Products: | Microcontrollers ,Arm Cortex-M0 MCUs ,M051 Base Series ,M0518 Series ,Mini51 Base Series ,Nano100/102 Base Series ,Nano110/112 LCD Series ,Nano120 USB Series ,Nano130 Advanced Series ,NUC029 Series ,NUC100/200 Advanced Series ,NUC120/122/123/220 USB Series ,NUC130/230 CAN Series ,NUC131/NUC1311 CAN Series ,NUC140/240 Connectivity Series ,Arm Cortex-M4 MCUs ,M451 Base Series ,M451M Series ,M452 USB Series ,M453 CAN Series ,NUC442/472 Series ,NUC505 Series |
|---|---|
| Applications: | |
| Function: | Peripherals,Memory,APROM,Config,Data Flash,Flash Memory Controller (FMC),LDROM,Software and Tools,Nu Tools,In Circuit Programming (ICP) Tool,In System Programming (ISP) Tool |